Ironweb Wall Assembly & Installation Guide
TIP-OVER RISK
This wall-mounted modular storage system must be permanently fixed to the wall.
IMPORTANT INFORMATION
Follow each step of the instruction carefully. Keep this information for further reference.
WARNING
Serious or fatal injuries can occur from wall-mounted system falling down. To prevent this wall-mounted system from falling down it must be permanently fixed to the wall with the included 2 1/2" Torx Wood Screws. Assembly should be carried out by a qualified person, because wrong installation may lead to this rack system falling down and causing injury or damage. Fastening screws for walls with wood studs are including. Use fastening devices suitable for the walls in your home. Assess the suitability of the wall to ensure that the fastening devices will withstand the forces generated. For advice on suitable fastening screws, contact your local hardware store.
PARTS INCLUDED:
Large System
- (a) 35" Straight Square Tubes x 2
- (b) 34" Square Tube Legs x 2
- (c) Top 49" Square Tube with Quick-Connect Couplings x 1
- (d) Bottom 49" Square Tube with Quick-Connect Couplings x 1
- (e) 24" Round Pipe with Female Connectors x 3
- (f) 9" Round Pipe with Quick-Connect Pin x 6
- (g) Face-Out Pipe Cap with Quick-Release Pin x 1
- (h) Quick-Release Pins x 6
Small System
- (a) 35" Straight Square Tubes x 2
- (b) 34" Square Tube Legs x 2
- (c) Top 25" Square Tube with Quick-Connect Couplings x 1
- (d) Bottom 25" Square Tube with Quick-Connect Couplings x 1
- (e) 24" Round Pipe with Female Connectors x 1
- (f) 9" Round Pipe with Quick-Connect Pin x 4
- (g) Face-Out Pipe Cap with Quick-Release Pin x 2
- (h) Quick-Release Pins x 4
TOOLS INCLUDED:
- (i) 2 1/2" Torx Wood Screws x 12
- (ii) 3/4" Pan Head Screws x 6
- (iii) No. 3 Phillips Head Screwdriver x 1
- (iv) No. 20 Torx Drive Bit x 1
TOOLS REQUIRED (not included):
- Drill
- Level
- Stud Finder
- Measuring Tape
ASSEMBLY STEP 1: installation video
Large System
Place (b) 34" Square Tube Legs 47" apart against wall, use a level to insure that legs are level.
Small System
Place (b) 34" Square Tube Legs 23" apart against wall, use a level to insure that legs are level.
STEP 2: Note: do not fasten (ii) 3/4" Pan Head Screws, this will be done in step 4.
Large System
Install (d) Bottom 49" Square Tube with Quick-Connect Couplings. Fasten the square tube legs to the wall using the provided (i) 2 1/2" Torx Wood Screws. Screws must be fastened to a wall stud. If stud cannot be located, heavy duty wall anchors must be used.
Small System
Install (d) Bottom 25" Square Tube with Quick-Connect Couplings. Fasten the square tube legs to the wall using the provided (i) 2 1/2" Torx Wood Screws. Screws must be fastened to a wall stud. If stud cannot be located, heavy duty wall anchors must be used.
STEP 3:
Large System
Install (a) 35" Straight Square Tubes.
Small System
Install (a) 35" Straight Square Tubes.
STEP 4:
Large System
Install (c) Top 49" Square Tube with Quick-Connect Couplings. Use a level to insure that wall system is level. Secure all square tube connections using (ii) 3/4" Pan Head Screws.
Small System
Install (c) Top 25" Square Tube with Quick-Connect Couplings. Use a level to insure that wall system is level. Secure all square tube connections using (ii) 3/4" Pan Head Screws.
INSTALLATION
Fasten the square tubes to the wall using the provided (i) 2 1/2" Torx Wood Screws. Screws must be fastened to a wall stud. If stud cannot be located, heavy duty wall anchors must be used. Use a level to ensure square tubes are level.
Large System
Small System
PIPE INSTALLATION Pipe installation video
Install (f) 9" Round Pipe with Quick-Connect Pin by pushing back female coupling sleeve and inserting pin. Sleeve will snap back when fully installed.
If using (f) 9" Round Pipe with Quick-Connect Pin as a face out, install the (g) Face-Out Pipe Cap with Quick-Release Pin. Simply slide cap on the end of 9" Round Pipe and insert quick-release pin.
For side hang pipe, install (e) 24" Round Pipe with Female Connectors to (f) 9" Round Pipe with Quick-Connect Pin by sliding Female end of 24" Round Pipe onto the slotted connector of 9" Round Pipe. Then insert quick-release pin.
Large System Only
When installing (e) 24" Round Pipe with Female Connectors side by side for a full 48" side hang, the (f) 9" Round Pipe with a wider slotted connector must be used.